Tell us about yourself!
How to Install Pergo FlooringView Instructable »
How to Fill a Keurig Automa...View Instructable »
How to Recycle Foam Into In...View Instructable »
How to Fix a Shaky Phone Ca...View Instructable »
Rough Sawn / Hewn BeamsView Instructable »
How to Fix an Electric Chai...View Instructable »
How to Replace an AirWheel ...View Instructable »
How to Fix an Overflowing W...View Instructable »
How to Fix Clothes Dryer St...View Instructable »
How To Feel YoungView Instructable »
How To Quickly Clear Snow a...View Instructable »
If you look at my video, when I have the cover off the humidifier, you can see a small circuit board on the right hand side. It has a transformer on it to supply 24 volts. My guess is that you need a new circuit board. Find the part number and google for it. I think it might be this one.http://www.generalaireparts.com/general-aire-ga4238-relay-circuit-board.html
If your Nest thermostat is not connected to the humidifier then it won't draw down the voltage. The humidifier fan runs on 120VAC and the little board makes 24VAC to go out to the humidistat and control the valve.
Where are you measuring this voltage? The humidifier should be powered with 120 Volts AC. In what way is your humidifier not working? What are the symptoms?
Yes, it looks like the very top of the p-trap has a nut that you can loosen. You then unscrew the nut directly under the sink and the drain should come up and out of the p-trap. All the replacement drains I have seen at the hardware store have poppers, so you may have to drill a hole for the popper push rod.
How To Build a Kitchen Fire...View Instructable »
Diamond blades are almost smooth with just a very fine coating of diamond dust. This means they are great for cutting things like tile and porcelain, because they grind away millions of microscopic particles, rather than larger chunks like most other blades. By taking smaller bites, the blade puts much less overall stress on the material being cut.
Yes, exactly, and it works exceedingly well. And it still works fine for overflow. Dual use.
Odorless Toilet for $35View Instructable »
Homemade Leaf Vacuum for $50View Instructable »
How To Make Soybean HummusView Instructable »
How To Rebuild a Washing Ma...View Instructable »
How To do a Rail Slide on a...View Instructable »
How To do a Fast Plant on a...View Instructable »
How To do a Shuvit on a Flo...View Instructable »
You need a more powerful fan. Also, that scraping screw takes a lot of energy from the motor. You need to get a ceiling fan with a really large wingspan. They typically have the most powerful motors. As you demonstrated, it wouldn't even start itself on the low setting. One more thing. On your next build, you might want to include a foot controlled on off switch. These cost about $20 and are typically used to control wood router tables. You put the motor on the highest speed setting, but only turn it on with the foot switch, when your hands are on the Clay, so it doesn't spin up too fast.
How To Fix a ShovelView Instructable »
A sedan wrap would be WAY too big!Seran wrap might work. I would rather have the zip lock. By the way, I finally got a Lifeproof case, but it leaks some. My speakers sound a little funny and the top left corner of my screen has a green shadow, after I took it under water. Funny thing though. My camera light has been broken for years, but it works fine when the phone gets wet :)
How To Install a Sump PumpView Instructable »
How To Install a Hardwood F...View Instructable »
Does your method kill the mole?
Actually, all you need is an on/off foot switch, and those are really easy to use. You just plug them into the outlet and plug your wheel into the switch. Look for a "momentary" or "deadman" foot switch. They cost about $20, and are typically used with power tools such as wood routers. Here is one I just found on Amazon.http://amzn.com/B000LJNJOEThis wheel runs at a good speed, if your hands are on the clay, but too fast, if not. Simply press on the pedal, when you are working, and let off otherwise.