Tell us about yourself!
What did you use to make that nice technical drawing?
Wine Barrel Adirondack Chair
I think you are missing the point of what Instructables is. This is a site of people that like to make things and not buy them off the shelf. The point of this Instructable is that kilns, like the one in your post, cost $500-$1000. You can build one yourself for fraction of that cost!
Homemade Anvil (from Rusty Railroadtrack)
I’m glad it helped!!!:)
how is this a runner up? You should have won!
Congrats on winning the contest. I can’t help but think that with all the work you did I on sanding you could have cast this in metal, either aluminum or brass.
Great project! I may build one. A futon mattress may be a great option because it could fold while in couch mode then lay flat when you pull out the bed.
Love the door! Great job!
Rustic Headboard With His a...View Instructable »
Sea Glass Pendant
Dip in a mixture of wax and linseed oil while hot. It will turn the iron black and prevent rust.
No, I don't think so. I made all my calculations based on 120V. Your voltage will change everything, I think.
DIY smart home doorbell for less than $40!
yes, to all of your questions. Just don't stretch it out too much when separating your coils or it will be too long. My outside diameter was a little bigger when I ended up making my own coil because my mandrel was 1/4" and the width of the wire pushed it up slightly over 3/8". I just filed my channels down a little and it fit fine. I think the last element I made was about 18 inches. You don't want to go much shorter than that or the kiln will heat up too fast with too little resistance. Please let me know if this helps and how your final kiln turns out!
Mine is a 15 Amp circuit so I tried to keep mine as short as possible without it heating up too much. Here's a website if you want more technical info. http://dcknives.blogspot.com/p/winding-kanthal-a1-element-for-an.html?m=1
There are formulas out there Dan. More by experience and trial and error though. My first element was too short and heated up too fast. I had to change the design of my top loader because of that.
Electric Kiln -- Top Loader View Instructable »
I updated the instructions to include an easier way to do this. There are brass connectors you can buy from some of the ceramics suppliers. I just used some steel bolts with two nuts to separate the wires.
No, I don't think so. I have since done some asking around. What you really want is either a PID controller (read some of the comments above) or an Infinity Control Switch (ICS kiln controller). Sundanceglass.com has one for sale.
if your coil is too short it will heat up too fast and the temperature will be hard to control. It may just heat up and burn out the coil. You definitely don't want to plug it directly into a wall outlet. Get a controller.
Probably not. I'm not an electrician, but I have mine in the garage and I can barely run anything else on that circuit without tripping the breaker. On dedicated circuit you will have enough heat to melt aluminum though.
Mine is a K-type thermocouple. I don't have a PID controller on mine, so i cant help you there. Look at some of the links in tge comments. Others have put pid controllers on theirs.
Because it is insulated with Kaowool. Lol
3D Printing Class
Cool! Nice work. Glad you found it helpful!
Hi, I'm not really sure the gauge on the door. I'm guessing about 22 or 24. It doesn't really matter as long as you can bend it with your fingers. Too thick and you will need a metal brake to form it.Hope that helps.
It's not really a source. It's a variable control. You plug it into a socket. It has no markings on it. I got it from an old table top kiln I bought off eBay.
Blacksmith A Wall Hanger
Raspberry PI-Getting started for newbie
Signet Ring From Nut
Ring box with wooden hinge
Casting Rings - From Startup to Finish
How to make a steampunk USB flash drive
Golden Snitch Ring
Make a gorgeous Dragon's Egg
Copper Rain Chain
High Quality (and Safe) Copper Plating
Building a Whiskey still
Lego Raspberry Pi case
Lego Raspberry Pi Case (for A & B model)
How To Hack An Apple Time Capsule With A Raspberry Pi
Growing Gourds (Ridge Gourd, Bitter Gourd and Snake Gourd)
spicy tomato coconut soup
Caldo De Marisco (Seafood Soup)
3D Printed spectrometer, using Public Lab DIY kit.
Solar Panel Setup around $100
Custom Coffee Table Ottoman
Leather Briefcase (Covert Edition)
Cast Aluminum Self Cocking Crossbow Pistol
Solar USB Charger 2.0
Make a takedown bow from skis!
Incredible Soda Bottle Pontoon Boat
Copper Rose - an everlasting flower!
How to Grow Oyster Mushrooms (Low Tech)
Wire Wrapped Pendants, the Easy Way
Homemade Rotary/Flat Engraver
Wall-Mounted Vertical Wood Wine Rack
Book of Shadows Celtic Knotwork Book
Minimalist Table from Reclaimed Floor Boards
From File to Knife (with simple tools)
100% Homemade Lathe
Celtic Knot Pendant
Turning a custom beer tap handle
Drywall Sanding Dust Collector/Separator
Inverted Sprinkler Experiment
Build a Concrete Computer Desk.
PVC Dremel drill press