Tell us about yourself!
TripComputer - GPS Trip Computer & Weather Module for Your Vehicle
FeatureCAM for Lathes Class
Drawstring Bag With Inner Pocket
Home Made Backpack
Star Trek Movie Jacket TWOK (The Wrath of Kahn) Costume
Went one step further and made a 90 degree working edge. I like to make stuff, sweatingthedetails.virb, then of course add dot com. I'm always trying to find something to upcycle and repurpose. Thanks
Fun little project
Power Supply for Etching With Salt Water
Custom Leather Knife Sheath
Drill Press Drum Sander
DIY Homemade Mini Wood Lathe With Drill Hand Tools
DIY Cloth Dopp Kit
Sewing Zippers and Buttons
Vegan French Onion Pho
Spanish Tortilla (Vegan)
Vegan Steakhouse Melts - Vegan Patties Folded and Stuffed With Vegan Cheese
Pumpkin Pie Truffles
Wooden Sheath for Cook's Knife
How to Make Leather Knife Sheath
Universal Leather Knife Sheath
Bison Leather Briefcase
Sewing Stretch on a Home Machine
Sewing Curved Seams
Great little project. I am going to make a few more tomorrow. These two are going to be gifts, and the others that I make will be for me to use instead of plastic bags.
How to Make Blacksmith Tongs
How to Build a Knife
How to Build a Gas Forge Burner
Hemming and Seam Finishing
Manly Mustache Groomer
Make a Barbarian's Sword
How to Make a Portable Bandsaw Table
Heat Treating Knives
Etching Large Metal Items
Piglet Shaped Wood Burner From an Old Bottle.
Reclaimed Wood Micro Teardrop Trailer
DIY Carbon Tape Heated Gloves V2.0
"Analog" Bicycle Speedometer
DIY Bicycle Turn Signal
Convert Your Van Into a Cosy Cabin for Under £400!
3D Printed Solar Bike Light for Less Than 2$
Tomahawk Survival Axe (that Opens Beers!)
Darth Vader Wood Burner Remix
The AXe Knife
Easy 3D Printing Class
Do you have a picture of this? It would help me out a lot. Thank you.
Thank you so much.
NES in a Cartridge
Make Your Own GPS SMS Security Tracking System
The Ultimate FM Transmitter (Long Range Spybug)
Edit* Since this isn't a very active thread and I want to finish this up, I just wend ahead and spliced the fan wires. I cut off the connector ends and spliced on longer wire wires then re-spliced the now longer wires onto the connector ends so that they could reach the circuit board. I just want it to look as clean and professional as possible. If anyone else runs into this issue, this is a route you can take.
Where is the 3d printer mount for the Z end stop holder? It's in one of the final pictures when the printer is done, but there are no prints or instructions about it? Nothing even on what size bolts it needs. Or even where it plugs into the board? Does anyone have the print for the z end stop holder?
Edit* to my comment, I did some digging on google and found out that I can either jump my power on wire (green wire) with a ground on the same pin or simply cut it splice it with a ground wire from that same large pin connector. I just needed further clarification. Since the instructions was a little hard for me to follow along.I hope this is able to help out anyone else that may be confused as well. I still need some help with my other questions. Unless I am able to figure those out too.
Hello all, I am nearly the end of the build. Right now I am having some trouble understanding how the power on (the green wire from the power supply) is spliced on to the ramps board? Matter a fact can someone please post up a picture of how the final wiring should be on the ramps board? I am a highly visual person, sometimes it's very hard for me to understand unless I can see it. I have combed over the instructions but I am still a little confused. Thank you. Oh also how/where do the wiring from the fan wire onto the ramp board? Mines are far to short to reach the board. Unless there are extentions that they hook up to.
Fireproof Carbon Foam from Pyrolysed Bread
The Soda Locker - Vending Machine
1000W Portable Induction Heater
Sewing Straight Seams
Machine Sewing Class
Easy Build Heat Treat Furnace - No power tools required.
Wooden Knuckle Dusters
Lucid Dream/Dream Recall Machine using infrared.
Make Basic Infrared Thermal Imaging Camera For Cheap ! Convert Any Camera Into Infrared Thermal Camera
DIY Infrared Night Vision Device
Raspberry PI night vision goggles.
Build a 10 Ton Hydraulic Press
20 Ton Air Operated Pan Brake/press Combo
Metal Brake Modified
5ton Press Brake Bender 3 in 1
Awesome Motorcycle Paint Idea
Energy friendly clothes iron (off grid use)!
Nixie Watch Prototype_C
Adult Onesie / Jumpsuit Pattern
The Audio Tesla Pistol
Mini Cleaver Build
How to Make an EMP Jammer
Teardrop Trailer Aluminum
Mochi with Coconut Icecream
Solar Heater for My Shop
Hand-Crafted Leather Cowboy Hat
★UNISEX BALACLAVA HAT★
Electromagnetic Climbing Like a Spiderman
How to make an iPod hat
How To Make a Brimmed Beenie
Two Daft Punk Helmets in One Month
Frankenstein Light Switch
Make a super-heroine shield
How to make a Daft Punk Guy Manuel Helmet and costume!
Building a Daft Punk helmet with programmable LED display
mini circular bench saw from scrap [UPDATED]
How to build a foam teardrop trailer. rot proof, well insulated and super lightweight